My cool blog 2876

Most homeowners judge a roof by what they can see: the shingles or metal panels on top. But the material that does the quiet, unglamorous work of keeping water out of your house is often the layer you never look at. Underlayment sits between the roof deck and the finish surface, and on a rainy island roof it can be the difference between a dry attic and a slow, hidden leak. In San Juan County, where roughly 40 inches of rain falls every year and November storms drive water sideways, understanding these layers helps you spend your roofing budget where it actually counts. What Underlayment Actually Does Underlayment is the sheet material installed directly over your roof deck (the plywood or OSB sheathing) before shingles or panels go on. Its job is to be a secondary water barrier. Wind-driven rain routinely pushes moisture underneath shingles and up around fasteners. Ice dams, moss buildup on shaded north slopes, and simple aging all create paths for water. When that happens, underlayment is what stops the water from reaching your wood deck and the living space below. Think of it as insurance. Your primary roof surface handles 99 percent of the weather. Underlayment handles the leaks your primary surface will eventually let through. The Three Main Types Roofers generally work with three categories of underlayment, and the right choice depends on slope, budget, and exposure. Asphalt-saturated felt is the traditional "tar paper," sold in 15-pound and 30-pound weights. It is inexpensive and time-tested, but it can wrinkle when it gets wet and tears more easily during installation. Synthetic underlayment is a woven polypropylene or polyethylene sheet. It is lighter, stronger, resists tearing, and holds up far better if it sits exposed for a few days before the roof surface goes on — a real advantage when ferry schedules delay material or crews. Self-adhering ice-and-water membrane is a peel-and-stick rubberized-asphalt sheet that bonds directly to the deck and seals around nails. This is the premium layer, reserved for the most vulnerable areas of the roof. Ice-and-Water Shield: Where It Belongs Despite the name, ice-and-water membrane matters on the islands far less for ice than for the sheer volume of wind-driven rain. This membrane creates a fully sealed, self-healing barrier — when a fastener punctures it, the rubberized asphalt grips the shank and closes around it. You do not need it across the entire roof on most homes. It belongs in the trouble spots: Valleys, where two roof planes meet and channel large volumes of water. Eaves, the lower edge where water collects and where ice dams can form during a cold snap. Around penetrations like chimneys, skylights, and vent pipes. Low-slope transitions, where a steep roof meets a shallower section. On coastal and exposed west-side homes — where wind can run roughly 20 percent stronger than nearby Anacortes — many builders extend membrane coverage further up rakes and eaves for extra protection. Comparing Your Options The table below is a general guide to help you weigh cost against performance. Figures are estimates, not a quote, and real pricing depends on roof size, slope, and access. Underlayment Type Relative Cost Best Use Lifespan Range 15/30-lb felt Lowest Budget re-roofs, steep slopes 12–20 years Synthetic sheet Moderate Full-roof primary layer 25–50 years Ice-and-water membrane Highest Valleys, eaves, penetrations 30–50 years Full-coverage membrane Premium Low-slope, high-exposure roofs 30–50 years A common island approach pairs a quality synthetic across the field of the roof with ice-and-water membrane in every valley, eave, and around every penetration. That combination balances cost and protection well for the local climate. Why This Matters More Near Saltwater Salt air is corrosive, and homes within sight of the water take a harder beating on fasteners and metal flashings. When those components loosen or corrode over decades, water finds the gaps. A properly sealed membrane layer under the flashings buys you time and reduces the odds of a leak reaching your deck before you catch it. Homeowners searching for https://sanjuanroofingco.com/ should first ask any prospective installer exactly which underlayment goes where, because the answer reveals how well the crew understands coastal conditions. Questions Worth Asking Before signing off on a re-roof, confirm these details in writing: Which underlayment covers the main field of the roof? How far up the eaves and valleys does the ice-and-water membrane extend? Are all penetrations getting membrane, not just tape or sealant? What fastener type is being used to hold the underlayment (corrosion-resistant matters near saltwater)? The Bottom Line Underlayment is not where you want to cut corners on a wet, windy island. The finish surface gets the attention, but the hidden layers determine whether your roof merely looks good or actually stays dry through a decade of November storms. A modest upgrade from bargain felt to a quality synthetic, plus targeted ice-and-water membrane in the vulnerable spots, is one of the highest-value decisions you can make during a re-roof. It costs a fraction of the total project and protects everything above and below it. When you review a roofing estimate, do not just compare shingle brands and panel colors. Read the underlayment line items. That is where a knowledgeable coastal roofer separates a roof built to survive island weather from one built to look fine on installation day. About the Author Marcus Reilly is a Pacific Northwest roofing consultant who has spent two decades inspecting and specifying roof assemblies for wet, wind-exposed coastal homes. He writes about building envelopes and moisture control for homeowners who want to understand what happens beneath the surface of their roofs.

The San Juan Islands take a beating from the weather. Between roughly 40 inches of rain a year and west-side winds that run about 20 percent stronger than they do over in Anacortes, a good windstorm can leave your roof compromised in ways you won't notice from the couch. The tricky part is that storm damage often hides in plain sight — a lifted shingle here, a loosened flashing seam there — and by the time water shows up on your ceiling, the problem has been quietly growing for weeks. This guide walks you through a safe, systematic inspection you can do yourself after the wind dies down. You don't need to climb onto a wet, steep roof to catch most problems. You need patience, a good pair of binoculars, and a clear idea of what you're looking for. Start Inside, Not Outside Counterintuitive as it sounds, the best place to begin is your attic. Interior clues often reveal a breach before anything is visible from the ground. Look for daylight. Pinholes of light through the roof deck mean gaps where wind-driven rain will follow. Check for wet insulation or dark streaks on the underside of the decking. Moisture stains point to an active or recent leak. Smell the air. A musty, damp odor after a storm suggests trapped moisture, which matters enormously in our wet climate. Feel the rafters for soft or spongy wood near the eaves and valleys, where ice-and-water membrane failures show up first. If you find any of these, note the location. It'll help you match interior clues to the exterior spot later. The Ground-Level Walk-Around Now head outside with binoculars. Walk the full perimeter of the house slowly and look up at every slope. Anyone chasing down https://sanjuanroofingco.com/ should learn to read a roof from the yard before ever setting foot on a ladder — most of what you need to see is visible from below. Here's your ground-level checklist: What to Look For What It Usually Means Missing or flipped shingles Wind uplift; underlayment now exposed Curled, cracked, or bruised shingles Aging or impact damage; loss of granules Granules piling in gutters Accelerated shingle wear from wind and rain Lifted or peeled flashing Compromised seal at chimneys, valleys, walls Bent or detached drip edge Water can now wick behind the fascia Debris piles (branches, needles) Trapped moisture and blocked drainage Sagging gutters or downspouts Overloaded during heavy rain; pulling away Take photos of anything that looks off. Zoom in with your phone or camera so you have a record — it's invaluable for tracking whether damage worsens and for any conversation with a contractor. Pay Special Attention to the Vulnerable Zones Not all parts of a roof fail equally. On island homes, certain areas take the brunt of wind and water. Valleys and Eaves These are where ice-and-water membrane belongs, and where water concentrates. After a storm, look for displaced shingles or exposed membrane in the valleys. At the eaves, check that the drip edge is still tight and that nothing is peeling. West- and South-Facing Slopes Because west-side wind is meaningfully stronger here, the windward slopes suffer the most uplift. Inspect these first and most carefully. A slope that faces the prevailing weather off the strait sees pressures a sheltered slope never will. Flashing and Penetrations Chimneys, plumbing vents, skylights, and wall junctions rely on flashing to stay watertight. Wind works flashing loose over time, and a single lifted seam is enough to let driven rain in. Salt air near saltwater doesn't help — it corrodes cheap fasteners and coatings, so older flashing on a waterfront home deserves extra scrutiny. North Slopes and Shaded Areas Under the Douglas firs, north-facing slopes stay damp and grow moss. A storm can rip moss-weakened shingles loose entirely. If you see green mats lifting at the edges, that's a section to watch. What to Do the Moment You Find Damage Speed matters in our climate. With rain never far off — and November the wettest month of all — an open breach can turn a small repair into a decking replacement fast. Contain the interior. Place buckets under active drips and move belongings clear. Document everything. Date-stamped photos of every problem area, inside and out. Don't attempt a permanent DIY fix on a steep or wet roof. A tarp secured properly by a professional is safer than a fall. Call for a professional inspection promptly. Ferry logistics mean island crews can't always come same-day, so get on the schedule early. Repair or Replace? A Quick Reality Check Once a professional has assessed the damage, you'll face the repair-versus-replace question. Here are rough ranges to frame the decision — an estimate, not a quote: Scenario Typical Cost Range Minor storm repair $450 – $3,500 Moss treatment (if damage is moss-related) $400 – $1,600 Full asphalt replacement $9,000 – $24,000 Standing-seam metal replacement $14,000 – $45,000+ If your roof is near the end of its life and a storm has caused widespread damage, repeated patching rarely pays off. Many island homeowners use a major storm as the moment to upgrade to standing-seam metal, which handles our wind, rain, and salt air far better and lasts 50 years or more. Build a Post-Storm Habit The homeowners who avoid nasty surprises are the ones who inspect after every significant blow, not just once a year. A ten-minute walk-around with binoculars, plus a quick attic peek, catches the small stuff before it becomes structural. Keep a simple log of dates and photos. Over time you'll know your roof's weak spots and can point a contractor straight to them. Your roof is the single most important barrier between your home and some of the wettest, windiest weather in the country. Treat every windstorm as a reason to look up — carefully, from the ground — and you'll spend far less over the life of the house. About the Author Marcus Delgado is a former residential inspector turned home-maintenance writer based in the Pacific Northwest. He focuses on practical, safety-first guidance that helps homeowners catch small problems before the rainy season turns them into expensive ones.

In the San Juan Islands, fall is the deadline. The heaviest rain arrives in November, wind pushes across the water harder on the west-facing slopes, and the roof you ignored all summer is about to be tested by roughly 40 inches of annual rainfall concentrated into the wet months. A weekend of maintenance now is the cheapest insurance you'll ever buy — a small repair caught in October costs a fraction of the interior damage a missed one causes in January. Here are the nine tasks worth doing before the storms settle in. 1. Clear the Gutters and Downspouts Under the Douglas firs, gutters fill with needles and leaves that turn into a soggy dam. Blocked gutters overflow behind the fascia, rot the eave, and in a cold snap force water back under the shingles. Flush every run, confirm downspouts drain well away from the foundation, and check that hangers are still tight. This is the single highest-return task on the list. 2. Treat and Remove Moss on Shaded Slopes Moss thrives on the north-facing slopes that sit in shade beneath the trees. It holds moisture against the roofing, lifts shingle edges, and shortens roof life. Fall is the time to treat it — before the growth explodes in the wet season. Do not pressure-wash asphalt shingles; it strips the protective granules. Use a gentle treatment and let the rain rinse it. Budget an estimate, not a quote, of $400–$1,600 for professional moss treatment depending on roof size and severity. Installing zinc or copper ridge strips at the same time releases metal ions that slow regrowth for years. 3. Inspect and Reseal Flashing Flashing — the metal at valleys, chimneys, skylights, and wall intersections — is where most island leaks actually start, not in the open field of the roof. Check for lifted edges, cracked sealant, and corrosion. Near saltwater, look hard for rust on fasteners and flashing metal, and confirm dissimilar metals aren't reacting. Reseal or replace anything questionable now. 4. Check Fasteners, Especially Near Saltwater Salt air corrodes cheap fasteners from the inside out. On metal roofs, walk the slopes and look for rust streaking below screw heads, backed-out screws, and hardened washers. On any roof within sight of saltwater, corroded fasteners are a leading cause of premature failure. Replace failing ones with stainless, corrosion-resistant hardware rather than matching the original builder-grade screws. 5. Look for Damaged, Lifted, or Missing Shingles Wind is stronger on the west side — roughly 20 percent stronger than across the water in Anacortes — so summer gusts may have already loosened material. From the ground with binoculars and, safely, from a ladder, scan for cracked, curled, lifted, or missing shingles and any exposed nail heads. Small shingle repairs run an estimate of $450–$3,500; letting them ride into November is how they become a full-slope problem. 6. Verify Valleys and Eaves Are Protected Valleys concentrate water, and eaves are where ice and backed-up water do their damage. Ice-and-water membrane belongs at both. If your roof predates modern underlayment standards or you've had eave leaks before, this is the detail to confirm — because researching https://sanjuanroofingco.com/ won't help if the water is already getting under the shingles at the most vulnerable points. Anywhere you see staining below a valley or eave, investigate before the wet season. 7. Trim Overhanging Branches Douglas fir and cedar limbs that scrape the roof abrade the surface, drop debris that feeds moss, and become projectiles in a windstorm. Cut branches back so they clear the roof by several feet. This also opens shaded slopes to a little more light and air, which slows moss naturally. 8. Inspect the Attic From Inside The best view of roof health is often from below. On a rainy day, go into the attic with a flashlight and look for daylight through the deck, water stains on the sheathing, damp or matted insulation, and any musty smell that signals trapped moisture. Confirm attic vents are clear — good ventilation keeps the deck dry and discourages condensation that mimics a leak. 9. Confirm Your Emergency and Documentation Plan Storm damage happens even to well-maintained roofs. Before November, know where your tarps and buckets are, photograph the roof in its current sound condition (dated photos help any future insurance claim), and keep a record of the maintenance you've done. That documentation proves the roof was healthy before a storm — the line between a covered claim and a "deferred maintenance" denial. Fall Maintenance Checklist at a Glance Task Priority DIY or Pro Rough Cost (estimate, not a quote) Clear gutters & downspouts High DIY / Pro $ — mostly time Treat/remove moss High Pro recommended $400–$1,600 Inspect & reseal flashing High Pro Repair $450–$3,500 Check fasteners near saltwater High Pro Included in repair scope Fix damaged/missing shingles High Pro $450–$3,500 Verify valley/eave membrane Medium Pro Varies Trim overhanging branches Medium DIY / Arborist $ — labor Inspect attic from inside Medium DIY Free Confirm emergency plan & photos Low DIY Free A Note on Island Timing and Cost Getting a crew and materials out to the islands adds roughly 10 to 25 percent over a comparable mainland job once ferry staging and off-island disposal are factored in. That premium is another reason to schedule non-emergency work in early fall rather than in a January downpour — you'll have your pick of dates, and you won't be paying rush logistics to fix something a $20 tube of sealant could have prevented in October. The Bottom Line None of these nine tasks is glamorous, and most cost little more than a Saturday and a ladder. But in a climate this wet, this windy, and this salty, fall maintenance is what separates a roof that quietly does its job for decades from one that fails at the worst possible moment. Work down the list before the November rains, and you'll spend the wet season dry. About the Author Ted Halloran is a home-maintenance writer and former general contractor who has cared for houses across the rainy Pacific Northwest for over two decades. He specializes in practical, seasonal upkeep for high-moisture coastal climates.

It is the question every island homeowner faces eventually: patch the roof one more time, or bite the bullet and replace it? Get it wrong in either direction and you lose money — pouring cash into a roof that is beyond saving, or tearing off one that had a decade left. This guide gives you a clear framework for deciding, calibrated to the specific realities of roofing in the San Juan Islands. Start With Three Questions Before you look at a single estimate, answer these. They resolve most cases on their own. 1. How old is the roof? Age is the strongest single signal. Asphalt shingles on an island typically last 15 to 25 years, less if moss has been neglected. Standing-seam metal can run 50 years or more. If your asphalt roof is past 20 and giving you trouble, you are usually replacing. If it is 8 years old with one leak, you are almost certainly repairing. 2. How widespread is the damage? A single leak at a flashing detail is a repair. Water showing up in several places, sagging areas, or daylight through the deck point to systemic failure. Localized problems get fixed; widespread ones get replaced. 3. What condition is the deck in? If the wood decking beneath the roofing is rotted or soft — a real risk after years of moss holding moisture on shaded north slopes — patching the surface solves nothing. Deck rot almost always tips the decision toward replacement. The Decision Table Use this to place your situation. Ranges are an estimate, not a quote, and reflect island pricing including ferry logistics — crew and material staging plus off-island disposal — which add roughly 10 to 25 percent over a comparable mainland job. Situation Repair Replace Estimated Cost One isolated leak, roof under 15 yrs ✔ $450 – $3,500 Moss present, no deck damage yet ✔ (treat) $400 – $1,600 Multiple leaks, roof 20+ yrs ✔ $11,000 – $40,000+ Rotted or sagging deck ✔ $11,000 – $40,000+ Failing flashing, sound roof ✔ $450 – $3,500 Frequent repairs, rising cost ✔ Asphalt $9k–$24k / Metal $14k–$45k+ Flat section, aging membrane ✔ or ✔ $8,000 – $26,000 When Repair Is the Right Call Repair wins when the roof is fundamentally sound and the problem is contained. Classic repair situations on island homes include: A leak traced to worn flashing around a chimney, skylight, or vent. Wind damage on the west side that lifted or tore a small area — island wind runs roughly 20 percent stronger than Anacortes, so localized wind damage is common. A cracked valley or a few displaced shingles. Moss that has taken hold but not yet rotted the deck. In these cases a targeted repair, plus preventive steps like ice-and-water membrane at the fixed valley and zinc or copper ridge strips to slow moss, buys you years at a fraction of replacement cost. When Replacement Is the Right Call Replacement wins when repairs are chasing a losing battle. Signs it is time: The roof is at or past its expected lifespan. You are repairing the same roof year after year, and the costs are climbing. Leaks appear in multiple, unrelated locations. The deck is soft, sagging, or rotted. Granules are washing into the gutters in quantity, or shingles are curling across whole slopes. Think in cost-per-year, not sticker price A $2,500 repair that buys two years costs you $1,250 a year. A $28,000 standing-seam metal roof that lasts 50 years costs $560 a year — and it is the best long-term island roof, resisting salt air, wind, and moss when built right. When you find yourself repeatedly repairing an old roof, the "cheaper" repair is often the more expensive choice over time. Island-Specific Factors That Tip the Balance A few things weigh more heavily here than on the mainland: Salt air. Near saltwater, corrosion attacks cheap fasteners and coatings. If a repair means matching an aging, already-corroding system, replacement with 24-gauge marine-grade metal and PVDF (Kynar 500) coating may make more sense sooner. Ferry logistics. Mobilizing a crew and staging materials on-island carries fixed costs. If you are going to pay to get a crew out for major work anyway, doing the job once and completely often beats repeated trips. Moss and rain. With 40 inches of rain a year and heavy November downpours, a marginal roof degrades fast. Deferring replacement on a failing roof risks deck rot that raises the eventual cost. Homeowners weighing these factors and searching for guidance on https://sanjuanroofingco.com/ should get a professional inspection before deciding — the deck condition in particular is hard to judge from the ground, and it frequently settles the question. A Simple Rule of Thumb If your roof is young and the damage is localized, repair. If your roof is old and the damage is widespread — or the deck is compromised — replace. When you are genuinely on the fence, weigh cost-per-year and the island's harsh conditions, both of which tend to favor doing the job right rather than patching indefinitely. The Bottom Line There is no universal answer, but there is a reliable method: assess age, extent of damage, and deck condition; place yourself on the decision table; then think in cost-per-year rather than sticker shock. Do that honestly, factor in salt, wind, moss, and ferry logistics, and you will spend your roofing dollars where they actually protect your home. About the Author Nathan Prewitt is a Salish Sea building inspector who has evaluated hundreds of roofs on the question of repair versus replacement. He specializes in helping island homeowners read the true condition of an aging roof before they commit to a decision.